- Coats Wheel Balancers
- Coats 1004 Wheel Balancer Manual Diagram
- Coats 1004 Wheel Balancer Manual Review
- Coats 1004 Wheel Balancer Manual Transmission
OUTER weight display. STATIC balance button. “MAG” balance button. Wheel diameter (D) knob. Wheel width (W) knob. Wheel offset (A) knob. Leave balancer power on all day. Static power use is approximately 70 watts. Mount Wheel Select proper adapter. Adapter selected should center wheel the same as the wheel is centered. 1996 Coats 1004 Wheel Balancer Unit is in good working order and comes with minimal cone assortment. Specifications: Cycle time 4-5 seconds, max. Outer tire diameter is 42”, wheel dia. 10” – 19.9”, wheel width 2.7” – 18.6”, modified tongue motor with: 900 RPM rating, forced air cooling, 1-1/2 HP rating, shipping weight 550 lbs. View & download of more than 27 Coats PDF user manuals, service manuals, operating guides. Tyre Changers, Wheel Balancers user manuals, operating guides & specifications.
Advertising
Connect to Power
Your factory trained COATS
®
Service Technician should do the
final check to verify the power installation before connecting the
balancer to a power supply. Failure due to improper power con-
nection will void the warranty.
balancer to a power supply. Failure due to improper power con-
nection will void the warranty.
Connect the balancer to an appropriate electrical receptacle.
Refer to Figure 8 and 9, as well as Electrical Requirements on
page 1.
page 1.
Note: If pedestrian or equipment traffic might damage the
standard power cord, power outlets must be enclosed in a race-
way on the floor or in an overhead drop.
way on the floor or in an overhead drop.
Note: Electric outlets must be solidly connected. There should
be less than 1 Ω electrical resistance between the ground pin
and earth ground. The installer or electrical inspector must ver-
ify the outlet installation before connecting the balancer. Failure
due to improper power connection will void the warranty.
and earth ground. The installer or electrical inspector must ver-
ify the outlet installation before connecting the balancer. Failure
due to improper power connection will void the warranty.
Note: The green wire in the cord is the grounding wire. Never
connect the green wire to a live terminal.
Initial Testing
This should be performed by your factory trained COATS
®
Coats Wheel Balancers
Service Technician.
1. If the circuit breaker for the balancer outlet is off, turn it on
now. Turn the balancer ON/OFF switch to ON.
Remember: To maintain the proper operating temperature for
the balancer, the unit should be left on all day.
2. The displays will show zeros when the unit is first turned
on. Press any key to continue.
3. Verify that the fan is running by placing your hand between
the arbor faceplate and the motor housing. You should feel air
coming out from around the motor housing. Do not operate the
balancer if airflow is not present when the balancer is on.
coming out from around the motor housing. Do not operate the
balancer if airflow is not present when the balancer is on.
4. Lower the hood and press START. The arbor faceplate
should spin in the direction indicated by the label at the outer
edge of the motor cover (clockwise when viewed straight on).
edge of the motor cover (clockwise when viewed straight on).
If the faceplate spins counterclockwise, turn the balancer off,
turn the circuit breaker off, and disconnect the balancer plug.
Swap two of the hot wires connected to the receptacle.
Reconnect the balancer to the receptacle, turn the circuit
breaker on, then turn the balancer on. Lower the hood and press
START and recheck the direction of the spin. The faceplate
should now be spinning in a clockwise direction.
Swap two of the hot wires connected to the receptacle.
Reconnect the balancer to the receptacle, turn the circuit
breaker on, then turn the balancer on. Lower the hood and press
START and recheck the direction of the spin. The faceplate
should now be spinning in a clockwise direction.
Note: Single-phase balancers will also spin in a clockwise
direction.
Note: Disregard a short spin cycle with HUB displayed on the
control panel during this initial testing.
5. Raise the hood during a spin cycle to verify that the hood
interlock system is functioning properly.
Direct Drive
COATS 1000/1000D Wheel Balancer • 5
Figure 8 - Three-Phase Wiring Diagram
Figure 9 - Single-Phase Wiring Diagram
Three-Phase
Ground
Hot
195-230 V
Between
Hot Wires
Between
Hot Wires
Hot
Hot
Coats 1004 Wheel Balancer Manual Diagram
Single-Phase
A – Red
B – Black
Green/
Ground
Advertising
Popular Brands
Popular manuals
WHEEL BALANCER
MORE THAN 300 used models IN STOCK. John Bean®, Hunter®, FMC®, Hoffman, Coats® computer balancers. New Motorcycle balancers in stock for immediate delivery AUTOMOTIVE EQUIPMENT, SHOP EQUIPMENT BALANCEADORA COMPUTARIZADA Balanceadora con rotación automática, motor y mango incorporado
Balanceadora de llantas basada en un microprocesador con motor y ciclo automático, con adaptador de cono incorporado en el mango y posicionador automático. Para llantas
CLICK HERE TO SEE TRUCK WHEEL BALANCERS - NEW - USED |
|
Allstates computer wheel balancer Platinum model Optional motorcycle adaptors available |
CLICK TO SEE LARGER PHOTO AND SPECS |
Allstate's Of America, Inc. 2595 NW 37TH. ST. MIAMI, FLORIDA 33142 USA 800 223 2573, 305 635-4525 Fax 305 635-5353 e-mail [email protected]http://www.allstates.com
Click to see Balancers and Tire Changers side by side |
COATS XR1750 RECONDITIONED COMPUTER WHEEL BALANCER
| |||
3-D and 2-D modes. Provides clear directions and operator prompts for easy balancing. Simultaneous display of static and dynamic data identifies any excess residual static imbalance. |
Coats 1004 Wheel Balancer Manual Review
C |
COATS® COMPUTER WHEEL BALANCERSBrand new models are also available. Call for lowest prices.
|
Famous Coats 1001 Computer Wheel Balancer. Known for it's durability and accuracy. Available in single phase 220 volts or 3 phase 22o volts. $1,500.00 3 Phase and $1,600.00 in single phase. refurbishes and ready to use. |
Hunter GSp9200 video wheel balancer. this one is almost new with very little use on it. Includes cones and standard warranty. |
HUNTER® A700 Computer Wheel Balancer220 volt 3 Phase only Reconditioned With adaptors Heavy duty, built to last Large quantity available Price $900.00 refurbished or good used price $700.00 Reconditioned 220 volt 1 phase electric Heavy duty World wide service available from Hunter Techs Adaptors included Simple to operate |
Hunter 8 HP 220 volts, 3 phase heavy duty truck wheel spinner Also have hunter mechanical balance heads and Hunter strobe light |
HUNTER LARGE TRUCK SPINNER AND STROBE LIGHT IN STOCK.
AMERMAC® TRUCK SPINNER AND STROBE BALANCER
220volt 3 phase 7.5 H.P.Includes Strobe light
Rugged, built to last
Reconditioned
Hunter® models also in stock
Also Hunter and Bear Strobe Lights
Amermac on-the-car-Truer available
Hoffman® Finish Balancer. Use it ON-The-Car to fine tune any balance job. used to correct any problem wheels or specialty wheels. This machine is in very nice original condition. shows very little wear and tear. Easy to operate. Built by 'Hoffman', the inventor of fine computerized wheel balancers. Includes many accessories.220 volt, one phase power. Sit on it and operate the spinner against the tire. Original paint and finish as pictured. Includes instruction book. Includes remote and connection cables. |
ALLSTATE'S MOTORCYCLE AND CAR BALANCER
Coats 1004 Wheel Balancer Manual Transmission
HAND SPIN, HIGH QUALITY, MOTORCYCLE BALANCER. WITH MOTORCYCLE ADAPTOR SET, THE PRICE IS $2,200.00 SELF CALIBRATION IS BUILT IN. EXTREMELY ACCURATE. 5 BALANCING PROGRAMS: NORMAL, STATIC, AND 3 DIFFERENT ALUMINUM WHEEL MODES. READS IN OUNCES OR GRAMS. ACCURATE TO 1 GRAM. 10' to 24' WHEEL 1.5' to 20' RIM WIDTH 110 VOLT POWER MAX WHEEL WEIGHT = 60KG. |